Related papers: Final Muon Emittance Exchange in Vacuum for a Coll…
We propose a novel scheme for final muon ionization cooling with quadrupole doublets followed by emittance exchange in vacuum to achieve the small beam sizes needed by a muon collider. A flat muon beam with a series of quadrupole doublet…
A high-energy muon collider scenario require a "final cooling" system that reduces transverse emittance by a factor of ~10 while allowing longitudinal emittance increase. The baseline approach has low-energy transverse cooling within…
A complete scheme for production and cooling a muon beam for three specified muon colliders is presented. Parameters for these muon colliders are given. The scheme starts with the front end of a proposed neutrino factory that yields bunch…
In the final cooling stages for a muon collider, the transverse emittances are reduced while the longitudinal emittance is allowed to increase. In previous studies, Final cooling used absorbers within very high field solenoids to cool…
A high-energy muon collider scenario requires a final cooling system that reduces transverse emittance to ~25 microns (normalized) while allowing longitudinal emittance increase. Ionization cooling using high-field solenoids (or Li Lens)…
A high-energy muon collider scenario requires a "final cooling" system that reduces transverse emittance by a factor of ~10 while allowing longitudinal emittance increase. The baseline approach has low-energy transverse cooling within…
Small muon beams increase the luminosity of a muon collider. Reducing the momentum and position spreads of muons reduces emittance and leads to small, cool beams. Ionization cooling has been observed at the Muon Ionization Cooling…
Accelerated muon beams have been considered for next-generation studies of high-energy lepton-antilepton collisions and neutrino oscillations. However, high-brightness muon beams have not yet been produced. The main challenge for muon…
A large admittance sector cyclotron filled with LiH wedges surrounded by helium or hydrogen gas is explored. Muons are cooled as they spiral adiabatically into a central swarm. As momentum approaches zero, the momentum spread also…
An intense beam of muons is needed to provide a luminosity on the order of 10$^{34}$ cm$^{-2}$s$^{-1}$ for a multi-TeV collider. Because muons produced by colliding a multi-MW proton beam with a target made of carbon or mercury have a large…
Emittance exchange mediated by wedge absorbers is required for longitudinal ionization cooling and for final transverse emittance minimization for a muon collider. A wedge absorber within the MICE beam line could serve as a demonstration of…
Progress on six dimensional ionization muon cooling with relatively small rings of magnets is described. Lattices being explored include scaling sector cyclotrons with edge focusing and strong focusing, fixed field alternating gradient…
The muon collider has the potential to be a powerful tool for the exploration of frontiers in particle physics. In order to reach high luminosity, the 6D emittance of the muon beam needs to be reduced by several orders of magnitude. The…
We discuss the design of the muon capture front end for a \mu+-\mu- Collider. In the front end, a proton bunch on a target creates secondary pions that drift into a capture transport channel, decaying into muons. A sequence of rf cavities…
Fast muon beam six dimensional (6D) phase space cooling is essential for muon colliders. The Helical Cooling Channel (HCC) uses hydrogen-pressurized RF cavities imbedded in a magnet system with solenoid, helical dipole, and helical…
A complete scheme for production, cooling, acceleration, and ring for a 1.5 TeV center of mass muon collider is presented, together with parameters for two higher energy machines. The schemes starts with the front end of a proposed neutrino…
Emittance exchange mediated by wedge absorbers can be used for longitudinal ionization cooling and for final transverse emittance minimization for a muon collider. A wedge absorber within the Muon Ionization Cooling Experiment (MICE) could…
Submitted as input for discussions on a possible low emittance muon accumulator at 50 TeV. I present a scheme to obtain high quality positive and negative muon beams in terms of low emittance, high charge and high energy using an…
Cooling of muon beams for the next-generation lepton collider is necessary to achieve its higher luminosity with fewer muons. In this paper we present an idea to combine ionization cooling with parametric resonances that is expected to lead…
Muon storage rings have been proposed for use as sources of intense high-energy neutrino beams and as the basis for muon colliders. Phase-space compression (cooling) of the muon beam prior to acceleration and storage is needed to optimise…