Related papers: Third generation residual gas ionization profile m…
Ion implantation underpins a vast range of devices and technologies that require precise control over the physical, chemical, electronic, magnetic and optical properties of materials. A variant termed recoil implantation - in which a…
We present the development of the FBCM23 ASIC designed for the Phase-II upgrade of the Fast Beam Condition Monitoring (FBCM) system built at the CMS experiment which will replace the present luminometer based on the BCM1F ASIC [1]. The FBCM…
In the intact brain, neural activity can be recorded using sensing electrodes and manipulated using light stimulation. Silicon probes with integrated electrodes and micro-LEDs enable the detection and control of neural activity using a…
We demonstrate an on-chip device utilizing the concept of artificial cavity magnon-polariton (CMP) coupling between the microwave cavity mode and the dynamics of the artificial magnetism in a split ring resonator. This on-chip device allows…
A system of permanent magnet quadrupoles (PMQs) is going to be realized by INFNLNS to be used as a collection system for the injection of laser driven ion beams up to 60 AMeV in an energy selector based on four resistive dipoles. This…
In autonomous quantum error correction the lifetime of a logical bosonic qubit can be extended beyond its physical constituents without feedback measurements. Leveraging autonomous error correction, we propose a second-generation gate-based…
Ionization chambers are essential for activity determinations in radionuclide metrology. We have developed a high-precision integrating-differentiating (int-diff) system for measuring small currents. It is anticipated to enhance the…
Studying the polarization and spectral distortion of the Cosmic Microwave Background (CMB) in tandem with intensity fluctuations of the Cosmic Infrared Background (CIB) allows us to verify our assumptions on cosmic inflation and investigate…
Detrimental beam dynamics effects limit performance of high intensity rapid cycling synchrotrons (RCS) such as the 8 GeV proton Fermilab Booster. Here we report the results of comprehensive experimental studies of various beam intensity…
A model predictive control (MPC) method for enhancing post-fault transient stability of a grid-forming (GFM) inverter based resources (IBRs) is developed in this paper. This proposed controller is activated as soon as the converter enters…
This chapter focuses on a hardware architecture for semi-passive Reconfigurable Intelligent Surfaces (RISs) and investigates its consideration for boosting the performance of Multiple-Input Multiple-Output (MIMO) communication systems. The…
The IOTA Proton Injector (IPI), currently under installation at the Fermilab Accelerator Science and Technology facility (FAST), is a machine capable of delivering 20 mA pulses of protons at 2.5 MeV to the Integrable Optics Test Accelerator…
In this paper, we present our approach to systematically measure numerous performance parameters of MCP-PMTs. The experimental setups, the analyses and selected results are discussed. Although the techniques used may be different in other…
The PIP-II accelerator is a proposed upgrade to the Fermilab accelerator complex that will replace the existing, 400 MeV room temperature LINAC with an 800 MeV superconducting LINAC. Part of this upgrade includes a new injection scheme into…
Injected beam energy and energy spread are critical parameters affecting the performance of our rapid cycling synchrotron (RCS). A real-time energy monitoring system is being installed to examine the H- beam out of the Intense Pulsed…
In this paper, we discuss the design and whole-cavity simulation of a Multi-Beam Inductive Output Tube (MBIOT) that uses a 3rd harmonic component to the drive voltage on the grid. High-efficiency inductive output tubes (IOTs) are typically…
A series of beam dynamic studies were performed in 2020-2021 at the PIP-II Injector Test Facility (PIP2IT) that has been built to validate the concept of the front-end of the PIP-II linac being constructed at Fermilab. PIP2IT is comprised…
Integrated photonic technologies have recently shown significant advances, enabling the possibility to implement reconfigurable interferometers with increasing size. One of the main tasks to fully exploit the capabilities of reconfigurable…
The Proton Improvement Plan-II (PIP-II) [1] has been developed at Fermilab to provide powerful proton beams to the laboratorys experiments. An 800-MeV superconducting linear accelerator-a centerpiece of the project-is currently under…
The characterization of an interior permanent magnet synchronous machine (IPMSM) requires numerical analysis of the nonlinear magnetic motor model in different load conditions. To obtain the case-specific best machine behavior, a strategy…