Related papers: Probabilistic Schmid factors and scatter of LCF li…
The analysis of standardized low cycle fatigue (LCF) experiments shows that the failure times widely scatter. Furthermore, mechanical components often fail before the deterministic failure time is reached. A possibility to overcome these…
Fatigue life of components or test specimens often exhibit a significant scatter. Furthermore, size effects have a non-negligible influence on fatigue life of parts with different geometries. We present a new probabilistic model for…
In the present work, theoretical approaches, based on grain orientation dependent Young's modulus and Schmid factor are used to describe the influence of local grain orientation on crack initiation behaviour of the coarse grained nickel…
The present work discusses the micro-mechanism of low cycle fatigue (LCF) crack growth in smooth bar specimens of Haynes 282. Two parametric approaches, i.e. crack tip opening angle (CTOA) and maximum tangential stress ({\theta}MTS) have…
An accurate risk assessment for fatigue damage is of vital importance for the design and service of today's turbomachinery components. We present an approach for quantifying the probability of crack initiation due to surface driven…
The onset of nonlinear effects in metals, such as plasticity and damage, is strongly influenced by the heterogeneous stress distribution at the grain level. This work is devoted to studying the local stress distribution of shear stresses…
The failure of a component often is the result of a degradation process that originates with the formation of a crack. Fatigue describes the crack formation in the material under cyclic loading. Activation and deactivation operations of…
Finite element modelling is conducted to simulate the stress redistribution around a broken fibre (BF) in a bundle with experimentally measured fibre diameter distributions (FDD), followed by a parametric study of the influence of the FDD…
A probabilistic risk assessment for low cycle fatigue (LCF) based on the so-called size effect has been applied on gas-turbine design in recent years. In contrast, notch support modeling for LCF which intends to consider the change in…
In recent years a local probabilistic model for low cycle fatigue (LCF) based on the statistical size effect has been developed and applied on engineering components. Here, the notch support extension based on the stress gradient effect is…
For the fatigue life of thin-walled components, not only fatigue crack initiation, but also crack growth is decisive. The phase-field method for fracture is a powerful tool to simulate arbitrary crack phenomena. Recently, it has been…
An accurate assessment for fatigue damage as a function of activation and deactivation cycles is vital for the design of many engineering parts. In this paper we extend the probabilistic and local approach to this problem proposed in [1,2]…
In this work, the finite elements method (FEM) is used to analyse the growth of fretting cracks. FEM can be favourably used to extract the stress intensity factors in mixed mode, a typical situation for cracks growing in the vicinity of a…
The damage mechanisms and load redistribution of high strength TC17 titanium alloy/unidirectional SiC fibre composite (fibre diameter = 100 $\mu$m) under high temperature (350 {\deg}C) fatigue cycling have been investigated in situ using…
Three-dimensional X-ray diffraction (3DXRD) has been used to measure, in-situ, the evolution of $\sim 1800$ grains in a single phase low carbon ferritic steel sample during uniaxial deformation. The distribution of initial residual grain…
In this work we propose a stochastic model for estimating the occurrence of crack initiations on the surface of metallic specimens in fatigue problems that can be applied to a general class of geometries. The stochastic model is based on…
The deformation and crack initiation mechanisms were analyzed in a textured AZ31B-O Mg alloy subjected to fully-reversed, strain-controlled cyclic deformation along the rolling direction after 50 cycles (approximately 33% of the fatigue…
The present study evidences the role of ferrite grain size distributions on the occurrence of void initiation in a low carbon steel. Various thermomechanical treatments were done to create ultrafine, bimodal and coarse range of ferrite…
Traditional computational approaches in simulating crack propagation in perfectly brittle materials rely on the estimate of stress intensity factors along the rupture front. This proves highly challenging in 3D when the crack geometry…
Stress corrosion cracking (SCC) is a form of failure in metals that is present mostly in systems where humidity contact and mechanical load play a key role. Therefore, prediction of the combined effect is desired. There are models based on…