Related papers: Non-singular assembly mode changing trajectories i…
Parallel robots admit generally several solutions to the direct kinematics problem. The aspects are associated with the maximal singularity free domains without any singular configurations. Inside these regions, some trajectories are…
When moving from one arbitrary location at another, a parallel manipulator may change its assembly-mode without crossing a singularity. Because the non-singular change of assembly-mode cannot be simply detected, the actual assembly-mode…
The goal of this paper is to explain, using a typical example, the distribution of the different assembly modes in the workspace and their effective role in the execution of trajectories. The singular and non-singular changes of assembly…
A family of reconfigurable parallel robots can change motion modes by passing through constraint singularities by locking and releasing some passive joints of the robot. This paper is about the kinematics, the workspace and singularity…
This paper investigates the singular curves in the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points play an important role in…
This paper investigates the cuspidal configurations of 3-RPR parallel manipulators that may appear on their singular surfaces in the joint space. Cusp points play an important role in the kinematic behavior of parallel manipulators since…
This paper demonstrates that any general 3-DOF three-legged planar parallel robot with extensible legs can change assembly modes without passing through parallel singularities (configurations where the mobile platform loses its stiffness).…
Cusps and nodes on plane sections of the singularity locus in the joint space of parallel manipulators play an important role in nonsingular assembly-mode changing motions. This paper analyses in detail such points, both in the joint space…
This paper investigates the singular curves in two-dimensional slices of the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points…
This paper proposes a new design method to determine the feasible set of parameters of translational or position/orientation decoupled parallel robots for a prescribed singularity-free workspace of regular shape. The suggested method uses…
This paper investigates the conditions in the design parameter space for the existence and distribution of the cusp locus for planar parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which…
The workspace topologies of a family of 3-revolute (3R) positioning manipulators are enumerated. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps that…
This paper presents an algorithm for detecting and computing the cusp points in the joint space of 3-RPR planar parallel manipulators. In manipulator kinematics, cusp points are special points, which appear on the singular curves of the…
This paper investigates the existence conditions of cusp points in the design parameter space of the R\underline{P}R-2P\underline{R}R parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which can…
We study in this paper a class of 3-RPR manipulators for which the direct kinematic problem (DKP) is split into a cubic problem followed by a quadratic one. These manipulators are geometrically characterized by the fact that the moving…
Cuspidal robots can travel from one inverse kinematic solution to another without meeting a singularity. The name cuspidal was coined based on the existence of a cusp point in the workspace of 3R serial robots. The existence of a cusp point…
This paper presents the kinematic analysis of the 3-PPPS parallel robot with an equilateral mobile platform and a U-shape base. The proposed design and appropriate selection of parameters allow to formulate simpler direct and inverse…
Workspace and joint space analysis are essential steps in describing the task and designing the control loop of the robot, respectively. This paper presents the descriptive analysis of a family of delta-like parallel robots by using…
This paper introduces the Omnidirectional Tractable Three Module Robot for traversing inside complex pipe networks. The robot consists of three omnidirectional modules fixed 120{\deg} apart circumferentially which can rotate about their…
This paper presents the kinematic analysis of the 3-PPPS parallel robot with an equi-lateral mobile platform and an equilateral-shaped base. Like the other 3-PPPS robots studied in the literature, it is proved that the parallel…