Related papers: Deformation Patterns and Surface Morphology in a M…
Atomistic deformation simulations in the nominally elastic regime are performed for a model binary glass with strain rates as low as $10^{4}$/sec (corresponding to 0.01 shear strain per 1$\mu$sec). A robust elasticity is revealed that…
Plastic deformation of crystalline and amorphous matter often involves intermittent local strain burst events. To understand the physical background of the phenomenon a minimal stochastic mesoscopic model was introduced, where…
Plastic deformation of micron-scale crystalline materials differ considerably from bulk ones, because it is characterized by random strain bursts. To obtain a detailed picture about this stochastic phenomenon, micron sized pillars have been…
Plastic yield of amorphous solids occurs by power law distributed slip avalanches whose universality is still debated. Determination of the power law exponents from experiments and molecular dynamics simulations is hampered by limited…
Necking instabilities, in which tensile (extensional) deformation localizes into a small spatial region, are generic failure modes in elasto-viscoplastic materials. Materials in this very broad class --- including amorphous, crystalline,…
A polycrystalline solid is modelled as an ensemble of random irregular polyhedra filling the entire space occupied by the solid body, leaving no voids or flaws between them. Adjacent grains can slide with a relative velocity proportional to…
Amorphous materials exhibit complex material proprteties with strongly nonlinear behaviors. Below a yield stress they behave as plastic solids, while they start to yield above a critical stress $\Sigma_c$. A key quantity controlling…
Stress and strain fields in a two-dimensional pixelwise disordered system are computed by a Fast Fourier Transform method. The system, a model for a ductile damaged medium, consists of an elastic-perfectly matrix containing void pixels. Its…
Models for fluid deformable surfaces provide valid theories to describe the dynamics of thin fluidic sheets of soft materials. To use such models in morphogenesis and development requires to incorporate active forces. We consider active…
The two key phenomena occurring in the process of ceramic powder compaction are the progressive gain in cohesion and the increase of elastic stiffness, both related to the development of plastic deformation. The latter effect is an example…
Plasticity is inherent to many engineering materials such as metals. While it can degrade the load-carrying capacity of structures via material yielding, it can also protect structures through plastic energy dissipation. To fully harness…
The shear-transformation-zone (STZ) theory of plastic deformation predicts that sufficiently soft, non-crystalline solids are linearly unstable against forming periodic arrays of microstructural shear bands. A limited nonlinear analysis…
In the present work, a method for the study of the structural deformations of two dimensional planar structures under uniaxial strain is presented. The method is based on molecular mechanics using the original stick and spiral model and a…
Stretching, drilling, and bending are the independent deformation modes of a thin shell, each of which has an individual energy content. When the energy content of a mode vanishes, that mode is neutral. We characterize all neutral modes of…
Engineering wear models are generally empirical and lack connections to the physical processes of debris generation at the nanoscale to microscale. Here, we thus analyze wear particle formation for sliding interfaces in dry contact with…
We study the two-dimensional (2D) shear flow of amorphous solids within variants of an elastoplastic model, paying particular attention to spatial correlations and time fluctuations of, e.g., local stresses. The model is based on the local…
The quasistatic behavior of a simple 2D model of a cohesive powder under isotropic loads is investigated by Discrete Element simulations. The loose packing states, as studied in a previous paper, undergo important structural changes under…
A micromorphic computational homogenization framework has recently been developed to deal with materials showing long-range correlated interactions, i.e. displaying patterning modes. Typical examples of such materials are elastomeric…
Discrete element (DEM) simulations demonstrate that granular materials are non-simple, meaning that the incremental stiffness of a granular assembly depends on the gradients of the strain increment as well as on the strain increment itself.…
Wrinkling is the phenomenon of out-of-plane deformation patterns in thin walled structures, as a result of a local compressive (internal) loads in combination with a large membrane stiffness and a small but non-zero bending stiffness.…