Related papers: TRAIL: Topology Authentication in RPL
Validating network paths taken by packets is critical for a secure Internet architecture. Any feasible solution must both enforce packet forwarding along endhost-specified paths and verify whether packets have taken those paths. However,…
In many application areas such as large-scale disaster detection, IoT networks connote the characteristics of LLN (Low power and Lossy Network). With few exceptions, prior work on RPL(Routing Protocol for LLN), a standard routing protocol…
The IPv6 over Low-powered Wireless Personal Area Network (6LoWPAN) protocol was introduced to allow the transmission of Internet Protocol version 6 (IPv6) packets using the smaller-size frames of the IEEE 802.15.4 standard, which is used in…
The motivation behind this paper is to dissecting the secure network for Business to Business (B2B) application by Implementing Access Control List (ACL) and Service Level Agreement (SLA). This data provides the nature of attacks reported…
Traceability greatly supports knowledge-intensive tasks, e.g., coverage check and impact analysis. Despite its clear benefits, the \emph{practical} implementation of traceability poses significant challenges, leading to a reduced focus on…
The Industrial Internet of Things (IIoT) refers to the use of interconnected smart devices, sensors, and other technologies to create a network of intelligent systems that can monitor and manage industrial processes. 6TiSCH (IPv6 over the…
The current standard of Routing Protocol for Low Power and Lossy Networks (RPL) incorporates three modes of security: the Unsecured Mode (UM), Preinstalled Secure Mode (PSM), and the Authenticated Secure Mode (ASM). While the PSM and ASM…
In this paper, we propose a new scheme that allows coupling beacon-enabled IEEE 802.15.4 with the RPL routing protocol while keeping full compliance with both standards. We provide a means for RPL to pass the routing information to Layer 2…
The ongoing trend to move industrial appliances from previously isolated networks to the Internet requires fundamental changes in security to uphold secure and safe operation. Consequently, to ensure end-to-end secure communication and…
Low-power wireless networks play an important role in the Internet of Things. Typically, these networks consist of a very large number of lossy and low-capacity devices, challenging the current state of the art in protocol design. In this…
To ensure secure and reliable communication in wireless systems, authenticating the identities of numerous nodes is imperative. Traditional cryptography-based authentication methods suffer from issues such as low compatibility, reliability,…
A critical requirement for modern-day Intelligent Transportation Systems (ITS) is the ability to collect geo-referenced data from connected vehicles and mobile devices in a safe, secure and anonymous way. The Nexagon protocol, which builds…
Advanced Persistent Threat (APT) attack usually refers to the form of long-term, covert and sustained attack on specific targets, with an adversary using advanced attack techniques to destroy the key facilities of an organization. APT…
Existing methods for active topology discovery within the IPv6 Internet largely mirror those of IPv4. In light of the large and sparsely populated address space, in conjunction with aggressive ICMPv6 rate limiting by routers, this work…
Everyone is concerned about the Internet security, yet most traffic is not cryptographically protected. The usual justification is that most attackers are only off-path and cannot intercept traffic; hence, challenge-response mechanisms…
The Resource Public Key Infrastructure (RPKI) protocol was standardized to add cryptographic security to Internet routing. With over 50% of Internet resources protected with RPKI today, the protocol already impacts significant parts of…
With the introduction of the smart grid, Advanced Metering Infrastructure (AMI) has become a main component in the present power system. The effective implementation of AMI depends widely on its communication infrastructure and protocols…
In mobile ad hoc networks, by attacking the corresponding routing protocol, an attacker can easily disturb the operations of the network. For ad hoc networks, till now many secured routing protocols have been proposed which contains some…
RPL, the routing protocol proposed by IETF for IPv6/6LoWPAN Low Power and Lossy Networks has significant complexity. Another protocol called LOADng, a lightweight variant of AODV, emerges as an alternative solution. In this paper, we…
Encrypted tunneling protocols are widely used. Beyond business and personal uses, malicious actors also deploy tunneling to hinder the detection of Command and Control and data exfiltration. A common approach to maintain visibility on…