Related papers: Output stages inside a negative feedback loop: app…
The purpose of this project was to design and implement a pipeline Analog-to-Digital Converter using 0.35um CMOS technology. Initial requirements of a 25-MHz conversion rate and 8-bits of resolution where the only given ones. Although…
This paper proposes and evaluates a novel architecture for a low-power Time-to-Digital Converter with high resolution, optimized for both integration in multichannel chips and high rate operation (40 Mconversion/s/channel). This converter…
Transistor is a three terminal semiconductor device normally used as an amplifier or as a switch. Here the alternating current (a.c) rectifying property of the transistor is considered. The ordinary silicon diode exhibits a voltage drop of…
We simulated an axial vircator with a three-cavity resonator and expected generation efficiency 6-7 percents. For adequate description of physical processes taking place inside a vircator we used two independent PIC codes: self-developed…
The constant phase element (CPE) with a frequency-independent negative phase between current and voltage is used extensively in e.g. the bioimpedance and electrochemistry fields. Its physical meaning is only partially understood. Here we…
Robust simulation is essential for reliable operation and planning of transmission and distribution power grids. At present, disparate methods exist for steady-state analysis of the transmission (power flow) and distribution power grid…
A critical challenge in power conversion in electric vehicles is the efficient use of DC-DC buck converters that need to provide 12-V supply for load systems from 400/800-V batteries. This paper presents a literature review on the…
A robust and portable power supply has been developed specifically for charging linear transformer drivers, a modern incarnation of fast pulsed power generators. It is capable of generator +100 kV and -100 kV at 1 mA, while withstanding the…
This paper describes a CMOS analogy voltage supper buffer designed to have extremely low static current Consumption as well as high current drive capability. A new technique is used to reduce the leakage power of class-AB CMOS buffer…
In this paper, we focused on the design of an adaptive backstepping controller (adaptive-BSC) for direct power control (DPC) of a three-phase PWM rectifier. In the proposed system, it is desired to control both the output DC voltage of the…
The design and measurement results of ultra-low power, fast 10-bit Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC) prototypes in 65 nm CMOS technology are presented. Eight prototype ADCs were designed using two…
A low cost, stable, programmable, unipolar current source is described. The circuit is designed in view of a modular arrangement, suitable for applications where several DC sources must be controlled at once. A hybrid switching/linear…
Global demand for clean and eco-friendly energy sources has inspired decades of far-reaching research in power generation from renewable energy sources. Solar cells, wind, and tidal sources are limited in output power generation compared to…
A four-stage operational transconductance amplifier (OTA) for ultra-low-power applications is introduced in this paper. The proposed circuit inclusive of frequency compensation requires minimal transistor count and passives, overcoming the…
Solar micro-inverters are becoming increasingly popular as they are modular, and they posses the capability of extracting maximum available power from the individual photovoltaic (PV) modules of a solar array. For realizing micro-inverters…
Power dissipation in integrated circuits is one of the major concerns to the research community, at the verge when more number of transistors are integrated on a single chip. The substantial source of power dissipation in sequential…
This paper describes a pipelined analog-to-digital converter (ADC) employing a power and area efficient architecture. The adjacent stages of a pipeline share operational amplifiers. In order to keep accuracy of the amplifiers in the first…
This paper proposes a novel multilevel inverter for automotive applications. The topology consists of a modular DCDC converter and a tap selector, where the DC-DC converter provides several DC-output levels and the tap selector produces an…
Conventional boost converters are essential to connect low-voltage energy source such as battery with high voltage DC bus in Electric Vehicles due to its simple construction and high conversion efficiency. However, large output capacitor…
Nanopositioning techniques currently applied to characterize physical properties of materials interesting for applications at the microscopic scale rely on high-voltage electronic control circuits that should have the lowest possible noise…