Related papers: Strengthening weak value amplification with recycl…
In a quantum-noise limited system, weak-value amplification using post-selection normally does not produce more sensitive measurements than standard methods for ideal detectors: the increased weak value is compensated by the reduced power…
Weak-value-amplification permits small effects to be measured as observable changes at the sacrifice of power due to post-selection. The power recycling scheme has been proven to eliminate this inefficiency of the rare post-selection, thus…
We improve the precision of the interferometric weak-value-based beam deflection measurement by introducing a power recycling mirror, creating a resonant cavity. This results in \emph{all} the light exiting to the detector with a large…
We apply the combined technique of postselected amplification and photon-recycling to an optical setup of magnetic field precision measurement. We propose two recycling schemes and carry out analytic expressions for the amplified signal and…
Weak measurement has been proven to amplify the detection of changes in meters while discarding most photons due to the low probability of post-selection. Previous power-recycling schemes enable the failed post-selection photons to be…
We show that weak measurement can be used to "amplify" optical nonlinearities at the single- photon level, such that the effect of one properly post-selected photon on a classical beam may be as large as that of many un-post-selected…
To describe the pre- and post-selected quantum ensembles, a complex quantity called the weak value of an operator is used. The weak value is highly controversial due to the fact that it is not bounded by the possible eigenvalues of the…
Most studies for postselected weak measurement in optomechanical system focus on using a single photon as a measured system. However, we find that using weak coherent light instead of a single photon can also amplify the mirror's position…
We study the possibility of varying the measured lifetime of a decaying particle based on the technique of weak value amplification in which an additional filtering process called postselection is performed. Our analysis made in a direct…
An interferometric arrangement is proposed in which the technique of weak value amplification is implemented in order to enlarge the effect of a single photon on the quadratures of a movable mirror of an optical cavity. The photon interacts…
An experimental proposal is presented in which dark port post-selection together with weak measurements are used to enlarge the radiation pressure effect of a single photon on a mechanical oscillator placed in the middle of a Fabry-Perot…
Weak measurements in combination with post-selection can give rise to a striking amplification effect (related to a large "weak value"). We show that this effect can be understood by viewing the initial state of the pointer as the ground…
The implementation of weak-value amplification requires the pre- and post-selection of states of a quantum system, followed by the observation of the response of the meter, which interacts weakly with the system. Data acquisition from the…
Due to the reduced probability of successful post-selection, the weak-value amplification seems to be unavailable for the parameter-estimation. Here, we show theoretically that, some effects due to the weak interactions present only in the…
We revisit the scheme of single-photon weak-coupling optomechanics using post-selection, proposed by Pepper, Ghobadi, Jeffrey, Simon and Bouwmeester [Phys. Rev. Lett. 109, 023601 (2012)], by analyzing the exact solution of the dynamical…
The application of postselection to a weak quantum measurement leads to the phenomenon of weak values. Expressed in units of the measurement strength, the displacement of a quantum coherent measuring device is ordinarily bounded by the…
I propose a scheme for reconstructing the weak value of an observable without the need for weak measurements. The post-selection in weak measurements is replaced by an initial projector measurement. The observable can be measured using any…
Postselected weak measurement is a useful protocol for amplifying weak physical effects. However, there has recently been controversy over whether it gives any advantage in precision. While it is now clear that retaining failed…
Weak measurement [1,19] combined with quantum delayed-choice experiment that use quantum beam splitter instead of the beam splitter give rise to a surprising amplification effect, i.e., counterintuitive negative amplification effect. We…
Weak measurement has garnered widespread interest for its ability to amplify small physical effects at the cost of low detection probabilities. Previous entanglement and recycling techniques enhance postselection efficiency and…