Related papers: Bending instabilities of soft tissues
Active control of wrinkling in soft film-substrate composites using electric fields is a critical challenge in tunable material systems. Here, we investigate the electro-mechanical instability of a soft dielectric film bonded to a…
We address the flutter instability of a flexible plate immersed in an axial flow. This instability is similar to flag flutter and results from the competition between destabilising pressure forces and stabilising bending stiffness. In…
We provide a clear energetic insight into the catastrophic nature of the so-called creasing and pull-in instabilities in soft electro-active elastomers. These phenomena are ubiquitous for thin electro-elastic plates and are a major obstacle…
The surfaces of growing biological tissues, swelling gels, and compressed rubbers do not remain smooth, but frequently exhibit highly localized inward folds. We reveal the morphology of this surface folding in a novel experimental setup,…
When a rubber block is sliding on a hard rough substrate, the substrate asperities will exert time-dependent deformations of the rubber surface resulting in viscoelastic energy dissipation in the rubber, which gives a contribution to the…
Metals deformed at high strain rates can exhibit failure through formation of shear bands, a phenomenon often attributed to Hadamard instability and localization of the strain into an emerging coherent structure. We verify formation of…
Surface roughness is a key factor when it comes to friction and wear, as well as to other physical properties. These phenomena are controlled by mechanisms acting at small scales, in which the topography of apparently-flat surfaces is…
This paper presents the stability analysis of a system composed of rotating beams on a flexible, circular fixed ring, using the Routh-Hurwitz criterion. The model displayed has been fully developed within the rotating frame by use of an…
Protein fibril accumulation at interfaces is an important step in many physiological processes and neurodegenerative diseases as well as in designing materials. Here we show, using $\beta$-lactoglobulin fibrils as a model, that semiflexible…
We study elastic ribbons subject to large, tensile pre-stress confined to a central region within the cross-section. These ribbons can buckle spontaneously to form helical shapes, featuring regions of alternating chirality (phases) that are…
Crumpling of a thin film leads to a unique stiff yet lightweight structure. The stiffness has been attributed to a complex interplay between four basic elements - smooth bends, sharp folds, localized points (developable cones), and…
Plasma proteins such as fibrinogen induce the aggregation of red blood cells (RBC) into rouleaux, which are responsible for the pronounced shear thinning behavior of blood, control the erythro- cyte sedimentation rate (ESR) a common…
Comparison of a few simple models of fluid and solid membranes illustrates how shear stresses can arise from a bending energy through a coupling between curvature and surface stresses, a feature incidental to the fluid or solid nature of…
We study the necking of a filament of complex fluid or soft solid subject to uniaxial tensile stretching, under conditions of constant imposed stress and force, by means of linear stability analysis and nonlinear simulations. We demonstrate…
The compression of soft elastic matter and biological tissue can lead to creasing, an instability where a surface folds sharply into periodic self-contacts. Intriguingly, the unfolding of the surface upon releasing the strain is usually not…
Bifurcation of an elastic structure crucially depends on the curvature of the constraints against which the ends of the structure are prescribed to move, an effect which deserves more attention than it has received so far. In fact, we show…
The structured deformation theory is used within the thermodynamics of irreversible processes framework in order to build a damage model relevant for quasi-brittle materials. The cracks are supposed smeared in the body and their shape is…
In jamming systems like colloids, emulsions, foams, and biological tissues, significant deformation is essential for processes such as material scraping or wound self-healing. To adequately spread a foam or cream over a surface, external…
Planning accurate manipulation for deformable objects requires prediction of their state. The prediction is often complicated by a loss of stability that may result in collapse of the deformable object. In this work, stability of a fabric…
The necking instability is a precursor to tensile failure and rupture of materials. A quasistatically loaded free-standing uniaxial specimen typically exhibits necking at a single location, corresponding to a long wavelength bifurcation…