Related papers: Cracking Condition of Cohesionless Porous Material…
We study a theoretical model of mud cracks, that is, the fracture patterns resulting from the contraction with drying in a thin layer of a mixture of granules and water. In this model, we consider the slip on the bottom of this layer and…
A particular failure mode of highly porous brittle materials consists in the propagation of cracks under uniaxial compressive loads. Such 'anticracks' have been observed in a range of materials, from snow and porous sandstone to brittle…
We investigate the wetting properties of the simplest element of an array of random fibers: two rigid fibers crossing with an inclination angle and in contact with a droplet of a perfectly wetting liquid. We show experimentally that the…
The evolution of porous structure and mechanical properties of binary glasses under tensile loading were examined using molecular dynamics simulations. We consider vitreous systems obtained in the process of phase separation after a rapid…
A lattice model for active matter is studied numerically, showing that it displays wettings transitions between three distinctive phases when in contact with an impenetrable wall. The particles in the model move persistently, tumbling with…
The rheology of cohesive granular materials, under a constant pressure condition, is studied using molecular dynamics simulations. Depending on the shear rate, pressure, and interparticle cohesiveness, the system exhibits four distinctive…
We derive here a linear elastic stochastic description for slow crack growth in heterogeneous materials. This approach succeeds in reproducing quantitatively the intermittent crackling dynamics observed recently during the slow propagation…
Due to their microstructure, quasi brittle materials present rough cracks. Under sliding of the crack lips, this roughness involves in one hand induced opening and in the other hand some apparent plasticity which is due to the interlocking…
Drying of bacterial suspensions is frequently encountered in a plethora of natural and engineering processes. However, the evaporation-driven mechanical instabilities of dense consolidating bacterial suspensions have not been explored…
We investigate the formation of spiral crack patterns during the desiccation of thin layers of precipitates in contact with a substrate. This symmetry-breaking fracturing mode is found to arise naturally not from torsion forces, but from a…
Differential shrinkage in particulate quasi-brittle materials causes microcracking which reduces durability in these materials by increasing their mass transport properties. A hydro-mechanical three-dimensional periodic network approach was…
The erosion and transport of particles by an impinging turbulent jet in air is observed in various situations, such as the cleaning of a surface or during the landing of a spacecraft. The presence of inter-particle cohesive forces modifies…
Stress corrosion cracking (SCC) is a form of failure in metals that is present mostly in systems where humidity contact and mechanical load play a key role. Therefore, prediction of the combined effect is desired. There are models based on…
Micro-droplets of soft matter solutions have different morphologies upon drying, and can finally become wrinkled, buckled or cavitated particles. We investigate the morphology evolution of a drying soft matter droplet in this work: at the…
Volume alteration in solid materials is a common cause of material failure. Here we investigate the crack formation in thin elastic layers attached to a substrate. We show that small variations in the volume contraction and substrate…
The adhesion dynamics of a membrane confined between two permeable walls is studied using a two-dimensional hydrodynamic model. The membrane morphology decomposes into adhesion patches on the upper and the lower walls and obeys a nonlinear…
The paper addresses the problem of a Mode III interfacial crack advancing quasi-statically in a heterogeneous composite material, that is a two-phase material containing elastic inclusions, both soft and stiff, and defects, such as…
We study the appearance and evolution of an array of parallel cracks in a thin slab of material that is directionally dried, and show that the cracks penetrate the material uniformly if the drying front is sufficiently sharp. We also show…
Using a phase field crystal model we study the structure and dynamics of a drop of colloidal suspension during evaporation of the solvent. We model an experimental system where contact line pinning of the drop on the substrate is…
We present an extension of the continuous damage fiber bundle model to describe the gradual degradation of highly heterogeneous materials under an increasing external load. Breaking of a fiber in the model is preceded by a sequence of…