Related papers: Wicking in a powder
The kinetics of spreading of a liquid drop in a wedge or V-shaped groove, in a network of such grooves, and on a hydrophilic strip, is re-examined. The length of a droplet of volume Omega spreading in a wedge after a time t is predicted to…
A solid substrate, when exposed to a vapour, can interact with it in such a way that sufficiently close to liquid-vapour coexistence a macroscopically thick liquid wetting layer is formed on the substrate surface. If such a wetting…
We employ a novel fluid-particle model to study the shearing behavior of granular soils under different saturation levels, ranging from the dry material via the capillary bridge regime to higher saturation levels with percolating clusters.…
Phase field theory is widely used to model multi-phase flows. A drop can shrink or grow spontaneously due to the redistribution of interface and bulk energies to minimize the system energy. In this paper, the spontaneous behaviour of a drop…
We present a quantitative comparison between extensive Monte Carlo simulations and self-consistent field calculations on the phase diagram and wetting behavior of a symmetric, binary (AB) polymer blend confined into a film. The flat walls…
This study considers the spreading of a Newtonian and perfectly wetting liquid in a square array of cylindric micropillars confined between two plates. We show experimentally that the dynamics of the contact line follows a Washburn-like law…
The effects of line tension on the morphology of a sessile droplet placed on top of a convex spherical substrate are studied. The morphology of the droplet is determined from the global minimum of the Helmholtz free energy. The contact…
The size-dependent contact angle and the drying and wetting morphological transition are studied with respect to the volume change for a spherical cap-shaped droplet placed on a spherical substrate. The line-tension effect is included using…
Control of the swelling, chemical functionalization, and adhesivity of hydrogels are finding new applications in a wide range of material systems. We investigate experimentally the effect of adsorbed particles on hydrogels on the depinning…
A simple numerical model is used to simulate the effect of vertical taps on a packing of monodisperse hard spheres. Our results are in agreement with an experimantal work done in Chicago and with other previous models, especially concerning…
Vapor-liquid menisci of the truncated and shifted Lennard-Jones fluid between parallel planar walls are investigated by molecular dynamics simulation. Thereby, the characteristic energy of the unlike dispersive interaction between fluid…
The influence of the external pressure and surface energy on the wetting transition at nanotextured interfaces is studied using molecular dynamics and continuum simulations. The surface roughness of the composite interface is introduced via…
Would a raindrop impacting on a coarse beach behave differently from that impacting on a desert of fine sand? We study this question by a series of model experiments, where the packing density of the granular target, the wettability of…
A sharp transition between liquefaction and transient solidification is observed during impact on a granular suspension depending on the initial packing fraction. We demonstrate, via high-speed pressure measurements and a two-phase…
The impact dynamics between wet surfaces, which dominates the mechanical properties of wet granular matter, is studied both experimentally and theoretically. It is shown that the hysteretic formation and rupture of liquid capillary bridges…
In relation to the interaction of the earth's surface with machines and organisms, and its engineering applications, there has been a recent increase in interest in the penetration resistive force into granular materials at shallow depths.…
Grain-boundary grooving is a general phenomenon occurring in all polycrystalline materials at the intersection between the grain-boundary and the interface or free surface. It has been studied theoretically for some time. Grain-boundary…
The effects of line tension on the morphology of a lens-shaped droplet and bubble placed on the inner wall of a spherical cavity are studied. The contact angle between the lens-shaped droplet and the concave spherical substrate is expressed…
The dip-coating geometry, where a solid plate is withdrawn from or plunged into a liquid pool, offers a prototypical example of wetting flows involving contact-line motion. Such flows are commonly studied using the lubrication approximation…
A dynamic wetting problem is studied for a moving thin fiber inserted in fluid and with a chemically inhomogeneous surface. A reduced model is derived for contact angle hysteresis by using the Onsager principle as an approximation tool. The…