Related papers: Expressing Properties of BPM Measurement System in…
The problem of errors, arising due to finite BPM resolution, in the difference orbit parameters, which are found as a least squares fit to the BPM data, is one of the standard problems of the accelerator physics. In this article we present…
A conventional method to determine beam parameters is using the profile measurements and converting them into the values of twiss parameters and beam emittance at a specified position. The beam information can be used to improve transverse…
With a Bayesian Gaussian regression approach, a systematic method for analyzing a storage ring's beam position monitor (BPM) system requirements has been developed. The ultimate performance of a ring-based accelerator, based on brightness…
For the PIP-II program, transverse emittance in the Fermilab Booster must remain well controlled at higher bunch intensities. 4-plate beam position monitors (BPMs) have a small but measurable quadrupole moment, making it possible to infer…
The measurement of beam emittances by extracting the quadrupole mode signal from a 4 plate beam position monitor (BPM) was published at least 40 years ago. Unfortunately, in practice, this method suffers from poor signal to noise ratio and…
The performance and safe operation of a particle accelerator is closely connected to the transverse emittance of the beams it produces. For this reason many techniques have been developed over the years for monitoring the transverse…
The measurement of the betatron tunes in a circular accelerator is of paramount importance due to their impact on beam dynamics. The resolution of the these measurements, when using turn by turn (TbT) data from beam position monitors…
The determination of beam parameters is essential for the operation and development of any accelerator facility. The working principle of frequently used beam instruments for electron and proton beams is discussed. The article comprises of…
This introduction on beam position monitors (BPM) summarizes the fundamental parts of the tutorial presented at the CAS 2018 on beam instrumentation. The focus is on the signal detection and normalization, and on the principle of operation…
In photo injectors, the transverse emittance is one of the key measures of beam quality as it defines the possible performance of the whole facility. As such it is important to measure the emittance in photo injectors and ensure the…
This paper introduces an axiomatic basis for measuring the energy characteristic of vibrating dynamical systems. The basic approach is to compare non-modulated vs. modulated waveforms in measuring energy during the vibratory motion $m(t)$…
Linear optics parameters are often estimated using readily available turn-by-turn (TbT) data. In-plane beta functions, which are the most common measurement objectives, can be estimated from the amplitudes or phases of TbT data, providing…
The fields produced by a long beam with a given transverse charge distribution in a homogeneous vacuum chamber are studied. Signals induced by a displaced finite-size beam on electrodes of a beam position monitor (BPM) are calculated and…
Generally, turn-to-turn power fluctuations of incoherent spontaneous synchrotron radiation in a storage ring depend on the 6D phase-space distribution of the electron bunch. In some cases, if only one parameter of the distribution is…
A beam-energy-spread monitor is under development in order to control and stabilize the energy spread of high-current single-bunch electron beams for producing a sufficient number of positrons. The author has proposed a new monitor using…
Virtually all commercial instruments for the measurement of the oscillator PM noise make use of the Cross Spectrum method (arXiv:1004.5539 [physics.ins-det], 2010). High sensitivity is achieved by correlation and averaging on two equal…
2D and 4D transverse phase-space of a low-energy ion-beam is measured with two of the most common emittance scanners. The article covers the description of the installation, the setup, the settings, the experiment and the benchmark of the…
A method to estimate linear chromaticity, RMS energy spread, and chromatic beta-beating, directly from turn-by-turn beam position data in a circular electron accelerator, is presented. This technique is based on frequency analysis of a…
The proof test and debugging of the multi-pulsed electron accelerator, Dragon-2,requires a thorough comprehension of the quality of the beams. This puts forward a rigid requirement on the measurement system that it should have the ability…
We present an improved system for orbit and betatron phase measurement utilizing nonlinear models of BPM pickup response. We first describe the calculation of the BPM pickup signals as nonlinear functions of beam position using Green's…