Related papers: From Brittle to Ductile Fracture in Disordered Mat…
Quasi-brittle behavior where macroscopic failure is preceded by stable damaging and intensive cracking activity is a desired feature of materials because it makes fracture predictable. Based on a fiber bundle model with global load sharing…
Refractory body-centered cubic (BCC) metals and alloys are of extraordinary importance in modern technological and structural applications. However, their wider adoption in science and technology is severely restricted by low-temperature…
Fractures are a critical process in how materials wear, weaken, and fail whose unpredictable behavior can have dire consequences. While the behavior of smooth cracks in ideal materials is well understood, it is assumed that for real,…
We combine an analytically solvable mean-field elasto-plastic model with molecular dynamics simulations of a generic glass-former to demonstrate that, depending on their preparation protocol, amorphous materials can yield in two…
We analyze large sets of energy-release data created by stress-induced brittle fracture in a pure sapphire crystal at close to zero temperature where stochastic fluctuations are minimal. The waiting-time distribution follows that observed…
Plasticity in soft amorphous materials typically involves collective deformation patterns that emerge upon intense shearing. The microscopic basis of amorphous plasticity has been commonly established through the notion of "Eshelby"-type…
The toughness of a polymer material can increase significantly if two networks are combined into one material. This toughening effect is a consequence of a transition from a brittle to a ductile failure response. Although this transition…
When brittle hydrogels fail, several mechanisms conspire to alter the state of stress near the tip of a crack, and it is challenging to identify which mechanism is dominant. In the fracture of brittle solids, a sufficient far-field stress…
We investigate the fracture process of a bundle of fibers with random Young modulus and a constant breaking strength. For two component systems we show that the strength of the mixture is always lower than the strength of the individual…
It was experimentally confirmed that if steel cyclic stress reduces to less than tensile yield stress values, i.e. in case of high-cycle fatigue, the mechanism of fracture changes from dislocation to vacancy one. This conclusion was based…
In ordinary solids, material disorder is known to increase the size of the process zone in which stress concentrates at the crack tip, causing a transition from localized to diffuse failure. Here, we report experiments on disordered 2D…
This work outlines a diffuse interface method for the study of fracture and fragmentation in ductile metals at high strain-rates in Eulerian finite volume simulations. The work is based on an existing diffuse interface method capable of…
A numerical realization of an elastic beam lattice is used to obtain scaling exponents relevant to the extent of damage within the controlled, catastrophic and total regimes of mode-I brittle fracture. The relative fraction of damage at the…
Unstable growth of cracks (rough crack surface and crack branching) in dynamic fracture has long been observed in various materials. Until now, there was no universally agreed upon explanation for these instabilities. Here, we demonstrate…
In this study, we address damage initiation and micro-crack formation in ductile failure of polycrystalline metals. We show how our recently published thermodynamic framework for ductile phase-field fracture of single crystals can be…
Highly-deformable materials, from synthetic hydrogels to biological tissues, are becoming increasingly important from both fundamental and practical perspectives. Their mechanical behaviors, in particular the dynamics of crack propagation…
The roughness exponent is reported in numerical simulations with a three-dimensional elastic beam lattice. Two different types of disorder have been used to generate the breaking thresholds, i.e., distributions with a tail towards either…
In this paper we analyze a system for brittle delamination between two visco-elastic bodies, also subject to inertia, which can be interpreted as a model for dynamic fracture. The rate-independent flow rule for the delamination parameter is…
We study the nonlinear rheology of a novel class of transient networks, made of surfactant micelles of tunable morphology reversibly linked by block copolymers. We couple rheology and time-resolved structural measurements, using synchrotron…
We introduce a model of fracture which includes the out-of-plane degrees of freedom necessary to describe buckling in a thin-sheet material. The model is a regular square lattice of elastic beams, rigidly connected at the nodes so as to…