Related papers: The ATLAS beam pick-up based timing system
The ATLAS BPTX stations are comprised of electrostatic button pick-up detectors, located 175 m away along the beam pipe on both sides of ATLAS. The pick-ups are installed as a part of the LHC beam instrumentation and used by ATLAS for…
The LHC timing signals are broadcast to various destinations in the subsequent experiments. And all of them could be delayed to time in the ATLAS sub-detectors by using the Corde board and the RF2TTC module. The ATLAS BPTX detectors and…
The ATLAS trigger system is based on three levels of event selection that select the physics of interest from an initial bunch-crossing rate of 40 MHz. During nominal LHC operations at a luminosity of 10^34 cm^-2 s^-1, decisions must be…
The ATLAS experiment took its first beam data in September 2008 and is actively preparing for the planned start of LHC collision data-taking in 2009. This preparation includes hardware and software commissioning, as well as calibration and…
The ATLAS detector is capable of resolving the highest energy pp collisions at luminosities sufficient to yield 10's of simultaneous interactions within a bunch collision lasting <0.5 nsec. Already in 2011 a mean occupancy of 20 is often…
Due to the huge interaction rates and the tough experimental environment of pp collisions at a centre-of-mass energy sqrt(s)=14TeV and luminosities of up to 10^34 cm^-2 s^-1, one of the experimental challenges at the LHC is the triggering…
The ATLAS experiment has been taking data efficiently since LHC collisions started, first at the injection energy of 450 GeV/beam and at 1.18 TeV/beam in 2009, then at 3.5 TeV/beam in 2010. Many results have already been obtained based on…
An extensive system test of the ATLAS muon spectrometer has been performed in the H8 beam line at the CERN SPS during the last four years. This spectrometer will use pressurized Monitored Drift Tube (MDT) chambers and Cathode Strip Chambers…
The ATLAS trigger has been used very successfully for the online event selection during the first part of the second LHC run (Run-2) in 2015/16 at a center-of-mass energy of 13 TeV. The trigger system is composed of a hardware Level-1…
The ATLAS Pixel detector is a high-resolution, low-noise silicon-based device designed to provide tracking and vertexing information within a distance of 12 cm from the LHC beam axis. It consists of approximately 80 million pixel channels…
We describe the main components of the ATLAS Forward Physics project, namely the movable beam pipe, the tracking and timing detectors which allow to detect intact protons in the final state at the LHC. The position detector is composed on 6…
The ATLAS detector is one of the experiments at the LHC that will detect high-energy proton collisions at 14 TeV. The commissioning of the detector has started already in 2005 in parallel to the detector installation and is still in…
The ATLAS trigger has been used very successfully to collect collision data during 2009 and 2010 LHC running at centre of mass energies of 900 GeV, 2.36 TeV, and 7 TeV. This paper presents the ongoing work to commission the ATLAS trigger…
The ATLAS experiment at the Large Hadron Collider employs a two-level trigger system to record data at an average rate of 1 kHz from physics collisions, starting from an initial bunch crossing rate of 40 MHz. During the LHC Run 2…
ATLAS is a multipurpose experiment at the LHC. The tracking system of ATLAS, embedded in a 2 T solenoidal field, is composed of different technologies: silicon planar sensors (pixel and microstrips) and drift-tubes. The procedure used to…
The early physics program at the ATLAS experiment includes measuring the basic properties of proton proton collisions, such as charged particle multiplicities, in order to constrain phenomenological models of soft interactions in the LHC…
During LHC Run 2 (2015-2018) the ATLAS Level-1 topological trigger allowed efficient data-taking by the ATLAS experiment at luminosities up to 2.1x10$^{34}$ cm$^{-2}$s$^{-1}$, which exceeds the design value by a factor of two. The system…
The ATLAS detector at CERN's Large Hadron Collider (LHC) will be exposed to proton-proton collisions from beams crossing at 40 MHz. At the design luminosity of 10^34 cm^-2 s^-1 there are on average 23 collisions per bunch crossing. A…
Detector control systems (DCS) include the read out, control and supervision of hardware devices as well as the monitoring of external systems like cooling system and the processing of control data. The implementation of such a system in…
ATLAS is one of the two general purpose detectors at the world's largest particle accelerator, the Large Hadron Collider (LHC). The LHC will be colliding proton beams at a center of mass energy {\surd}s= 14 TeV and is currently operating at…