Related papers: A Microcantilever-based Gas Flow Sensor for Flow R…
Separated flow transition is a very popular phenomenon in gas turbines, especially low-pressure turbines (LPT). Low-fidelity simulations are often used for gas turbine design. However, they are unable to predict separated flow transition…
We have developed a coupled level set and volume of fluid-based computational fluid dynamics model to analyze the droplet formation mechanism in a square flow-focusing microchannel. We demonstrate a flexible manipulation of droplet…
Thermal transient measurement based on source-drain voltage is a standard method to characterize thermal properties of silicon semiconductors but is doubtful to be directly applied to silicon carbide (SiC) devices. To evaluate its…
We study the buckling of a clamped beam immersed in a creeping flow within a rectangular channel. Via a combination of precision experiments, simulations, and theoretical modeling, we show how the instability depends on a pressure feedback…
Due to limitations in available sensor technology, unmanned aerial vehicles (UAVs) lack an active sensing capability to measure turbulence, gusts, or other unsteady aerodynamic phenomena. Conventional in situ anemometry techniques fail to…
Low efficiency is the main drawback of many MEMS thermal energy harvesters. Recently, energy harvesting micro-devices that operate using the pyroelectric effect gained attention due to their potential superior performance. Operation of…
In assessing piezoresistive microcantilever sensitivity for surface stress sensing, the key is its capacity to translate surface stress into changes in resistance. This change hinges on the interplay between stresses and piezoresistivity.…
We conduct a numerical study of the transient phenomenon in pipelines transporting plastic Bingham slurry flows, using a lowest-order finite element method (FEM). While most pipeline hammer studies focus on Newtonian fluids, the transient…
This novel piezoelectric zinc oxide (ZnO) thin film microcantilever was fabricated by micromachining technique. To release the cantilever, wet anisotropic etching of Silicon (Si) was performed by tetramethyl ammonium hydroxide (TMAH). The…
In the present study, a 1-dimensional model is proposed to estimate the pressure drop and heat transfer coefficient for flow boiling in a rectangular microchannel. The present work takes into account the pressure fluctuations caused due to…
The dynamics of solute flow in the microscopic chamber can be studied with optical tweezers. A method based on the metallic microbeads trapped in the focused optical vortex beam is proposed. This annular beam of a twisted wavefront exerts…
A variety of experimental techniques for the generation of subsonic/supersonic dust fluid flows and means of measuring such flow velocities are presented. The experiments have been carried out in a $\Pi-$shaped Dusty Plasma Experimental…
The measurement of acetone in human breath, a known biomarker for diabetes, can act as an effective screening method for diabetes. While gas chromatography and mass spectroscopy based methods can detect gases in low concentration, they are…
By revisiting the century-old problem of water bridge, we demonstrate that it is in fact dynamic and comprises of two coaxial water currents that carry different charges and flow in opposite directions. This spontaneous separation is…
Resistance force exerted on an obstacle in a gravity-driven slow granular silo flow is studied by experiments and numerical simulations. In a two-dimensional granular silo, an obstacle is placed just above the exit. Then, steady discharge…
Motivated by problems arising in the pneumatic actuation of controllers for micro-electromechanical systems (MEMS), labs-on-a-chip or biomimetic soft robots, and the study of microrheology of both gases and soft solids, we analyze the…
Control surface deployment in a supersonic flow has many applications, including flow control, mixing, and body-force regulation. The extent of control surface deflections introduces varying flow unsteadiness. The resulting fluid dynamics…
Electron-beam (e-beam) lithography is commonly used in fabricating metal-oxide-silicon (MOS) quantum devices but creates defects at the Si/SiO$_2$ interface. Here we show that a forming gas anneal is effective at removing shallow defects…
The dynamic yield stress associated with the flow cessation of cement pastes is measured using a rheometer equipped with various shear geometries such as vane, helical, sandblasted co-axial cylinders, and serrated parallel plates, as well…
In this work we present the design of a new test geometry inspired by the Tapered Double Cantilever Beam (TDCB) specimen that is shown to provide an improved characterization of the fracture properties of brittle solids. First, we show that…