Related papers: Studies of Polymer Deformation and Recovery in Hot…
We report on the development of some process capabilities for a polymer-based, multi-layer microelectrofluidic platform, namely: the hot embossing process, metallization on polymer and polymer bonding. Hot embossing experiments were…
Micro-indentation test with a micro flat-end cone indenter was employed to simulate micro embossing process and investigate the thermo-mechanical response of ceramic green substrates. The laminated low temperature co-fired ceramic green…
We report on the hot roller embossing of polymer sheets for the creation of microfluidic structures. Measurements conducted on 100 $\mu$m features showed that the lateral dimensions could be replicated to within 2% tolerance, while over 85%…
Ceramics are typically brittle at ambient conditions due to their covalent or ionic bonding and limited dislocation activities. While plasticity, and occasionally superplasticity, can be achieved in ceramics at high temperatures through…
The deformation kinetics for glassy polymers confined in microscopic domain at very low temperature regime was investigated using a transition-rate-state dependent model considering the shear thinning behavior which means, once material…
We present a thermal activated solvent bonding technique for the formation of embedded microstrucutres in polymer. It is based on the temperature dependent solubility of polymer in a liquid that is not a solvent at room temperature. With…
The investigation of the deformation behaviour of intermetallic phases is mostly limited to high temperatures due to their low ductility at ambient temperature. Therefore, within this study, nanoindentation experiments on the Al$_{2}$Cu…
Bonding between polymers below the glass transition temperature through molecular-scale dilatation (or densification)-based interdiffusion of macromolecules has recently been introduced. In this mechanism, short timeframe plastic…
In MEMS technology, most of the devices are fabricated on glass or silicon substrate. However, this research presents a novel manufacture method that is derived from conventional hot embossing technology to fabricate the electrostatic…
The advances in new technologies have prompted the need for functional systems smaller than the gyration radius of polymer chains. Thus, understanding how nanoconfinement affects polymer properties has been the focus of a lot of research…
The plastic deformation of Polybutylene terephthalate (PBT) is investigated at three temperatures (120$^\circ$C, 150$^\circ$C, 180$^\circ$C) representative of the span between glass transition, $T_g \approx 55^\circ$C and melting $T_m…
Bonding between polymeric interfaces is encountered widely in several industrial applications. Many of these bonding processes rely on time-consuming and temperature-dependent classical mechanism of polymer interdiffusion via reptation in a…
A coarse-grained molecular dynamics model of linear polyethylene-like polymer chain system was built to investigate the responds of structure and mechanical properties during uniaxial deformation. The influence of chain length, temperature,…
Heavy plastic shear deformation at relatively low homologous temperatures is called high-pressure torsion (HPT) deformation, which is one method of severe plastic deformation (SPD). The aim of the paper is to give an overview of a new…
Magnesium (Mg) and its alloys have a great potential as structural materials due to their beneficial combination of high strength to weight ratio, high thermal conductivity and good machinability. However, few literatures about Mg coatings…
The thermal effects of plastic and frictional heat generation and elevated temperature were examined along with the role of adhesion in the context of galling wear, using a representative crystal plasticity, normally loaded, sliding surface…
Multilayered ceramic substrates with embedded micro patterns are becoming increasingly important, for example, in harsh environment electronics and microfluidic devices. Fabrication of these embedded micro patterns, such as micro channels,…
Dewetting of ultrathin (< 100 nm) polymer films, by heating above the glass transition, produces droplets of sizes of the order of microns and mean separations between droplets of the order of tens of microns. These relatively large length…
Polymer self-adhesion due to the interdiffusion of macromolecules has been an active area of research for several decades [70, 43, 62, 42, 72, 73, 41]. Here, we report a new phenomenon of sub-Tg, solid-state, plasticity-induced bonding;…
The impact of severe plastic deformation by high-pressure torsion on the relaxation of the glassy and supercooled liquid states of Pd$_{40}$Ni$_{40}$P$_{20}$ was investigated using a combination of differential scanning calorimetry,…