Related papers: Film transitions of receding contact lines
The moving-contact line between a fluid, liquid and a solid is a ubiquitous phenomenon, and determining the maximum speed at which a liquid can wet/dewet a solid is a practically important problem. Using continuum models, previous studies…
We study a solid plate plunging into or being withdrawn from a liquid bath, to highlight the fundamental difference between the local behavior of an advancing or a receding contact line, respectively. It is assumed that the liquid partially…
The dynamics of the deformations of a moving contact line on a disordered substrate is formulated, taking into account both local and hydrodynamic dissipation mechanisms. It is shown that both the coating transition in contact lines…
A solid object can be coated by a nonwetting liquid since a receding contact line cannot exceed a critical speed. We theoretically investigate this forced wetting transition for axisymmetric menisci on fibers of varying radii. First, we use…
We report a molecularly-augmented continuum-based computational model of dynamic wetting and apply it to the displacement of an externally-driven liquid plug between two partially-wetted parallel plates. The results closely follow those…
We study the dewetting of a porous plate withdrawn from a bath of fluid. The microscopic contact angle is fixed to zero and the flow is assumed to be parallel to the plate (lubrication approximation). The ordinary differential equation…
We studied the dynamics of a liquid contact line receding on a hydrophobic soft gel (SBS-paraffin). In order to realize a well-defined geometry with an accurate control of velocity, a dip-coating setup was implemented. Provided that the…
The dynamics of the deformations of a moving contact line is formulated. It is shown that an advancing contact line relaxes more quickly as compared to the equilibium case, while for a receding contact line there is a corresponding slowing…
A prototypical problem in the study of wetting phenomena is that of a solid plunging into or being withdrawn from a liquid bath. In the latter, de-wetting case, a critical speed exists above which a stationary contact line is no longer…
The relaxation of a dewetting contact line is investigated theoretically in the so-called "Landau-Levich" geometry in which a vertical solid plate is withdrawn from a bath of partially wetting liquid. The study is performed in the framework…
When a plate is withdrawn from a liquid bath a coating layer is deposited whose thickness and homogeneity depend on the velocity and the wetting properties of the plate. Using a long-wave mesoscopic hydrodynamic description that…
The dynamics of receding contact lines is investigated experimentally through controlled perturbations of a meniscus in a dip coating experiment. We first characterize stationary menisci and their breakdown at the coating transition. It is…
We consider a porous solid covered with a water film (or with a drop) in situations where the liquid is pumped in, either spontaneously (if the porous medium is hydrophilic) or mechanically (by an external pump). The dynamics of dewetting…
When a contact line (CL) -- where a liquid-vapor interface meets a substrate -- is put into motion, it is well known that the contact angle differs between advancing and receding CLs. Using non-equilibrium molecular dynamics simulations, we…
When a solid plate is withdrawn from a partially wetting liquid, a liquid layer dewets the moving substrate. High-speed imaging reveals alternating thin and thick regions in the entrained layer in the transverse direction at steady state.…
The entrainment of air by advancing contact lines is studied by plunging a solid plate into a very viscous liquid. Above a threshold velocity, we observe the formation of an extended air film, typically 10 microns thick, which subsequently…
We consider the deposition of a film of viscous liquid on a flat plate being withdrawn from a bath, experimentally and theoretically. For any plate speed $U$, there is a range of ``thick'' film solutions whose thickness scales like…
In part 1, we proposed a model of dynamics of wetting for slow movements near a contact line formed at the interface of two immiscible fluids and a solid when viscous dissipation remains bounded. The contact line is not a material line and…
We establish the existence of a cusp in the curvature of a solid sheet at its contact with a liquid subphase. We study two configurations in floating sheets where the solid-vapor-liquid contact line is a straight line and a circle,…
The understanding of the spreading of liquids on solid surfaces is an important challenge for contemporary physics. Today, the motion of the contact line formed at the intersection of two immiscible fluids and a solid is still subject to…